BIQU BIGTREETECH MANTA M5P Mainboard
BIGTREETECH MANTA M5P Mainboard
32 Bit Controllerboard for DIY 3D Printers like Voron V0 and Creality Ender 3
- Manufacturer: BIQU
- Manufacturer number: 1020000409
- EAN: 4260395365856
- Item number: 36304
- Availability: from stock > delivery time 1-3 working days
Any questions about this article?
More articles in this category
BIGTREETECH Manta M5P is the successor of Manta M4P
- Manta all-in-one board + CB1 is more convenient to use Klipper firmware (CB1 is not included)
- DIY 3D printer for i3 structure
- ARM Cortex-M0+ series with 32-bit frequency of 64MHz STM32G0B1RET6 main control chip
- Increase the E-FUSE new fuse, which can respond quickly and enhance Self-protection ability, greatly reducing the damage caused by short circuit or ignition motherboard burnout.
- NC fan 24V, 12V, 5V voltage optional
- Jumper selection, support PT1000
- SPI and UART working modes driven by onboard TMC
- Onboard DIAG function pin
- Reserve SPI expansion interface for customers using Klipper firmware
- External acceleration sensor for acceleration compensation
| Dimensions: | 137.5mm x 95mm |
| Mounting Size: | Please refer to BIGTREETECH MANTA M5P V1.0-SIZE-top.pdf |
| MCU | ARM Cortex-M0+ STM32G0B1RET6 64MHz |
| Driver Input Voltage | VIN (DC12V-24V), HV (DC24V-56V) Selectable |
| Motherboard Input Voltage: | VIN=DC12V or DC24V |
| Logic Voltage: | DC 3.3V |
| Heater Connection: | Heated Bed (HB), Heater Cartridge (HE0, HE1) |
| HB Port Max Current: | 10A Continuous, 11A Instantaneous |
| Heater Cartridge Max Current: | 5.5A Continuous, 6A Instantaneous |
| Fan Port: | 3 x 2 pins CNC (FAN0, FAN1, Pi-FAN) (5/12/24V Selectable Voltage), 1 x Always On (FAN) |
| Fan Port Max Current: | 1A Continuous, 1.1A Instantaneous |
| Overall Current of Fan Ports): | ＜2.5A |
| Expansion Port: | CAN, Probe, RGBx2, SPI, EXP1+EXP2, MIN1-MIN4, 40Pin-GPIO |
| Motor Driver: | Support TMC5160, TMC2209, TMC2225, TMC2226, TMC2208, TMC2130, ST820, LV8729, DRV8825, A4988... |
| Driver Mode: | SPI, UART, STEP/DIR |
| Motor Driver Port: | Motor1, Motor2, Motor3 (Dual Motors Port), Motor4, Motor5 5 Channels in Total |
| Thermistor: | 3 x 100K NTC, two of which are selectable for NTC and PT1000 |
| Display: | SPI Touchscreen, LCD Display, HDMI Touchscreen, DSI Touchscreen |
| PC Connection: | Type-C |
| Interface: | USB 2.0x2, LAN, DSI, CSI, SPI, HDMI0, HDMI1, SOC-Card, MCU-Card |
| Supported Kinematics: | Cartesian, Delta, Kossel, Ultimaker, CoreXY |
| Recommended Slicer/Console: | Cura, Simplify3D, Pronterface, Repetier-host, Makerware |